国产国产人在线成免费视频

    <var id="tbxrt"><ins id="tbxrt"></ins></var>

        <big id="tbxrt"><listing id="tbxrt"></listing></big>
          <span id="tbxrt"><menuitem id="tbxrt"><dfn id="tbxrt"></dfn></menuitem></span>

          Shenzhen Grande Electronic Linkedin Page
          Shenzhen Grande Electronic Co., Ltd logo
          E-mail us for a Quote:
          sales88@greattong.com
          Call us now:
          +86-755-83261869

          Technical Article


          SMT: Pin-in-Paste Reflow Calculations and Special Cases

          Time:2017-09-20 17:09:41 Click:

          The major concern of the pin-in-paste SMT reflow process is the quality of the solder joint. It must meet IPC610 standard. The criteria for IPC610, class 2 are: 
          ? Both sides of the wire leads must obtain at least a 75% solder coverage
          ? Air cavities should be less than 30%
          ? The surface of the drilling as well as the component’s lead must have 100% wetting.

          To meet the above requirements, the following steps need to be considered: 
          ? Solder alloy volume calculation
          The volume between the hole and pin (Vsolder >= V hole + V fillet – V pin) should be filled up by the solder alloy with good fillet. 
          ? Minimum applied paste volume calculation
          Solder paste contains about 50% of metal material and 50% additional material (flux) which oozes out during the reflow process. So the minimum paste volume requirement is: 
           V paste = 2 x Vsolder = 2 x (Vhole + V fillet – Vpin) 
          ? Stencil aperture oversize design
          The area of the aperture is calculated as follows: 
           Apaste = Vpaste / Stencil (where the Stencil = the stencil thickness.) 
           The Stencil aperture size is calculated as follows: 
           If it is a circle, then the Dstencil = 2 x SQRT(Apaste / π ) , where Dstencil is aperture diameter. 
           If it is square, then the Lstencil = SQRT(Apaste ), where the Lstencil is the aperture length. 
           If it is rectangle, then Apaste = Lstencil x Wstencil, where the Lstencil is the aperture length and Wstencil is its width. 
           In most of situations, the aperture size will be bigger than pad’s size. This means that the solder paste will cover or extend over the entire hole. 
          ? Double Stroke: Special Paste Printing
          To get enough paste into the hole, double stroke is an acceptable process when the right pressure is applied. The squeegee print speed should be adjusted at a slower rate to let the paste fill the apertures more completely. This causes more solder paste to be deposited. 

          Previous:SMT:Reflow oven zone temperature set up and thermal profile

          Next:SMT: The Application of the Pin-in-Paste Reflow Process


          Request an Official Quote

          Questions

          E-MAIL

          File Upload

          Upload a list of files

            Please upload your Gerber files and BOM. You can upload an unlimited number of files as long as the total size of all files does not exceed 20 MB. To ensure you receive your official quote in less than 24 hours, please include the quantity of circuit boards for which you would like a quote.

            If you require that we sign a Non-Disclosure Agreement (NDA), please send it to us prior to sending your files and we will be happy to accommodate.

             
            Home About Us Services Quality Pb-Free News Contact Us


            Copyright ® 2017,Shenzhen Grande Electronic Co., Ltd. All Rights Reserved. 中文站 Sitemap

            国产国产人在线成免费视频

              <var id="tbxrt"><ins id="tbxrt"></ins></var>

                  <big id="tbxrt"><listing id="tbxrt"></listing></big>
                    <span id="tbxrt"><menuitem id="tbxrt"><dfn id="tbxrt"></dfn></menuitem></span>